How to Install the Flasher Hazard 7-Mode Autosensor

How to Install the Flasher Hazard 7-Mode Autosensor: A Guide to Enhanced Motorcycle Safety and Customization

The Flasher Hazard 7-Mode Autosensor is a cutting-edge module that can greatly enhance your motorcycle's safety and aesthetics. With seven different flashing modes and an automatic sensor feature, this device is a must-have for motorcycle enthusiasts looking to customize their rides. In this article, we will provide a step-by-step guide to installing the Flasher Hazard 7-Mode Autosensor, ensuring a seamless and effective setup.

Step 1: Gather the Necessary Tools and Components

Before beginning the installation, make sure you have all the required components, including the Flasher Hazard 7-Mode Autosensor module and the necessary tools such as wire cutters, strippers, electrical tape, and connectors. Having everything prepared will ensure a smooth installation process.

Step 2: Identify the Wires

The Flasher Hazard 7-Mode Autosensor module comes with five wires that need to be connected during the installation. To avoid confusion, identify each wire as follows:

• Two green wires: These wires are intended to be connected to the positive (+) terminals of the left and right turn signal lights.
• One red wire: This wire should be connected to the positive (+) terminal of the motorcycle's power source.
• One blue wire: This wire needs to be connected to the ground (-) terminal of the motorcycle.
• One small white wire: This wire is meant to be connected to the original flasher of your motorcycle.

Step 3: Prepare the Motorcycle

To begin the installation process, park your motorcycle in a safe and well-lit area. Turn off the engine and disconnect the battery to prevent any electrical mishaps during the installation.

Step 4: Access the Turn Signal Lights

Locate the left and right turn signal lights on your motorcycle, which are usually positioned on the front and rear sides of the bike. Carefully remove any fairings or panels covering the turn signal lights to access the positive (+) terminals.

Step 5: Connect the Green Wires

Take the two green wires from the Flasher Hazard 7-Mode Autosensor module and connect them securely to the positive (+) terminals of the left and right turn signal lights. Ensure a tight and reliable connection to avoid any loose wiring issues.

Step 6: Connect the Red Wire

Next, connect the red wire from the Flasher Hazard 7-Mode Autosensor module to the positive (+) terminal of the motorcycle's power source. This connection will supply power to the flasher, allowing it to function properly.

Step 7: Connect the Blue Wire

Connect the blue wire from the Flasher Hazard 7-Mode Autosensor module to the ground (-) terminal of your motorcycle. This establishes a grounding connection, which is crucial for the proper functioning of the flasher.

Step 8: Connect the White Wire

Finally, connect the small white wire from the Flasher Hazard 7-Mode Autosensor module to the original flasher of your motorcycle. This wire serves as an automatic sensor, enabling the flasher to function seamlessly. However, it is essential to note that if this white wire is not connected to the original flasher or not used, the automatic sensor feature will be disabled, but the flasher will still work.

Step 9: Secure the Connections

After connecting all the wires, use electrical tape and wire connectors to secure and insulate each connection. This will prevent any accidental disconnections or short circuits, ensuring a safe and reliable installation.

Step 10: Reassemble and Test

Reassemble any fairings or panels that were removed earlier to access the turn signal lights. Reconnect the battery, start the engine, and test the Flasher Hazard 7-Mode Autosensor module to ensure all the flashing modes and automatic sensor features are functioning correctly.

Conclusion:

With this step-by-step guide, you can easily install the Flasher Hazard 7-Mode Autosensor module on your motorcycle. Enjoy the benefits of enhanced safety and customizable flashing modes, all while elevating your bike's aesthetics. The automatic sensor feature adds an extra layer of convenience to your riding experience. Embrace the possibilities and ride with confidence using the Flasher Hazard 7-Mode Autosensor!

To get this product, you can contact the manufacturer directly
Telephone/Whatsapp : +6283821898789